Duro-last Metal Compression System Bedienungsanleitung PDF herunterladen

Duro-Last: The Proven Performer®

"Duro-Last" and The "World's Best Roof" are registered marks owned by Duro-Last , Inc.

DATA SHEET

www.duro-last.com

800-248-0280

DURO-LAST® METAL COMPRESSION

SYSTEM

Description:

The Duro-Last® Metal Compression System may be

used as a perimeter flashing for the Duro-Last roofing

system. The system consists of a Galvalume steel base

and a snap-on metal cover. The system is listed by

FM Approvals as a Class 1 perimeter flashing with the

4 inch (102 mm) wide system achieving a Class 1-360

and the 6 inch (152 mm) wide system achieving a Class

1-135.

 The base is fabricated from 24-gauge Galvalume

steel and comes in 10 foot lengths. The base is

available in widths ranging from 3 to 8 inches

(76-203 mm).

 The metal cover is 10 feet long and available in

24-gauge galvalume steel with 35 stocked finishes

as well as in these specialized metals:

* .040 aluminum with Kynar finish.

* .040 aluminum with mill finish.

* 16-oz. copper.

* 24-gauge stainless steel.

* 24-gauge bonderized (paintable) steel.

Contact Duro-Last, Inc. to request a color chart,

samples and information regarding custom metals and

finishes.

Installation:

1. A wood nailer is required if 1 inch or greater of

insulation is used. The top of the nailer must be flush

with the top of the insulation.

2. Fasten the flange of the metal base with fasteners

spaced 6 inches on center. When installing the base

within 10 feet of an outside corner the fastening

pattern is 3 inches on center.

3. Bring the roof membrane over the base and fasten it

6 inches on center into the vertical face of the metal

base. When installing within 10 feet of an outside

corner the fastening pattern is 3 inches on center.

4. Install the metal cover over the base and membrane.

5. The metal cover should be installed so that the joints

between sections are offset a minimum of 12 inch

(25 mm) from the joints between sections of the

metal base.

6. Adjacent sections of cover are designed to overlap.

No joint clips are required.

7. Refer to detail drawing 3110 for installation

information when roof system is mechanically

attached or FA3110 when the roof system is fully

adhered.

Note:

 The metal base and metal cover are ordered

separately in 10 foot lengths. They will be packaged

in cardboard tubes or wooden crates.

 The cover is shipped with a protective plastic film

which should be removed prior to installation.

 To clean the metal cover use soap and water (i.e.

1/3 cup laundry detergent per gallon of water).

Metal Compression System

(see details 3100 & FA3110)

Revised: 12/15/2011

DURO-LAST® METAL COMPRESSION 1

Inhaltsverzeichnis

Seite 1 - DURO-LAST® METAL COMPRESSION

Duro-Last: The Proven Performer®"Duro-Last" and The "World's Best Roof" are registered marks owned by Duro-Last , Inc.DATA SH

Kommentare zu diesen Handbüchern

Keine Kommentare

Duro-last Metal Compression System Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Duro-last Metal Compression System herunter. Duro-Last Metal Compression System User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Duro-last Metal Compression System